My Cart:

0 item(s) - £0.00
You have no items in your shopping cart.

0

01925 790 860

Victron MultiPlus Inverter Charger

Victron Multiplus Inverter Charger.
Available in 3 DC voltage ranges (12V,24V and 48V) the Victron Multiplus is a versatile inverter charger (combi) for use in off grid systems, back up systems, telecommunications systems, marine and auto systems.  Delivering 230V AC in pure sinewave format the Multiplus can power all of you electronic equipment.  The Victron Multiplus comes in 5 output sizes (800VA to 3000VA) for 12VDC or 24VDC and 2 output sizes (3000VA and 5000VA) for 48VDC. 

Need More Than 5kVA?
If you need more power than the maximum from a single Victron Multiplus, you can parallel uip to six of the 5000 units together.  Giving a total of 30kVA or 25,000 Watts.

Whats more if you need a 3 phase solution, just use 3 Multiplus' (1 for each phase).  It's that simple, you could have six Multiplus on each phase.

Do you occasionally need more power than what you grid supply can give?
Use a Victron Multiplus (with a battery bank) to provide grid assist for those times when you need that bit extra.   

Multi-functional, with intelligent power management

The Victron MultiPlus is a powerful pure sine wave inverter and battery charger in one unit.  It features adaptive charge technology, and a high-speed AC transfer switch in a single compact enclosure. Next to these primary functions, the Victron MultiPlus has several advanced features, as outlined below.

Two AC Outputs
The main output has no-break functionality. The Victron MultiPlus takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on one of the inputs of the MultiPlus. Loads that should not discharge the battery, like a water heater for example, can be connected to this output (second output available on models rated at 3kVA and more).

PowerControl - Dealing with limited generator, shore side or grid power
The Victron MultiPlus is a very powerful battery charger. It will therefore draw a lot of current from the generator or shore side supply (nearly 10A per 5kVA Multi at 230VAC). With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus preventing the generator or shore supply from being overloaded.

PowerAssist - Boosting the capacity of shore or generator power
This feature takes the principle of PowerControl to a further dimension. It allows the Victron MultiPlus to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery.

Four stage adaptive charger and dual bank battery charging
The main output provides a powerful charge to the battery system by means of advanced ‘adaptive charge’ software. The software fine-tunes the three stage automatic process to suit the condition of the battery, and adds a fourth stage for long periods of float charging. The adaptive charge process is described in more detail on the Phoenix Charger datasheet and on our website, under Technical Information. In addition to this, theMultiPlus will charge a second battery using an independent trickle charge output intended for a main engine or generator starter battery (trickle charge output available on 12V and 24V models only).

System configuring has never been easier
After installation, the MultiPlus is ready to go. If settings have to be changed, this can be done in a matter of minutes with a new DIP switch setting procedure. Even parallel and 3-phase operation can be programmed with DIP switches: no computer needed! Alternatively, VE.Net can be used instead of the DIP switches. And sophisticated software (VE.Bus Quick Configure and VE.Bus System Configurator) is available to configure several new, advanced, features.

Installation Service
We offer an installation service for all our Multiplus inverter/chargers.  Prices vary depending on location and inverter model.  Call 01925 790 860 for more information.

16 Item(s)

Grid  List 

16 Item(s)

Grid  List